This section considers station A as an example to describe the configuration process of the 52TOM board.
Precautions
NOTE: The OptiX OSN 6800A and OptiX OSN 3800A do not support ODU1_ANY_ODU0 re-encapsulation mode (OTU1->ODU1->Any->ODU0) in non-cascading mode.
NOTE: Each optical interface supports access of services at a maximum rate of 1.25 Gbit/s.
NOTE: The client-side eight pairs of optical interfaces can access services at a maximum rate of 10 Gbit/s.
Procedure
- Set the Working Mode of the 52TOM board. In the NE Explorer, select a 52TOM board, and choose from the Function Tree. Set Board Working mode to Non-Cascading and then set Port Working Mode to ODU1_ANY_ODU0 re-encapsulation mode (OTU1->ODU1->Any->ODU0). For details, see Configuring the Working Mode of the 52TOM Board.
- In the NE Explorer, select the desired board , and choose from the Function Tree. Set the Service Mode of the client-side interface of 52TOM as OTN mode. For details, refer to Configuring the Service Mode.
NOTE:
When the 52TOM board accesses OTU1 services on the client side, you first need to set the Service Mode of the 52TOM board to OTN mode.
- In the NE Explorer, select the desired board , and choose from the Function Tree. Set the Service Type for the WDM interface on the 52TOM board to OTU1 and also set the Service Type for the in-use AnyLP interfaces. For details, refer to Configuring the Service Type.
- Configure the OTU1 cross-connection between the RX/TX and ClientLP interfaces on the 52TOM board.
- Configure an OTU1 cross-connection between the 3(RX1/TX1) interface and the 201(ClientLP1/ClientLP1) interface on 52TOM board.
Parameters Value Level
OTU1
Service Type
-
Direction
Bidirectional
Source Slot
Shelf2(Subrack2)-15-52TOM
Source Optical Port
3(RX1/TX1)
Source Optical Channel (eg.1,3-6)
1
Sink Slot
Shelf2(Subrack2)-15-52TOM
Sink Optical Port
201(ClientLP1/ClentLP1)
Sink Optical Channel (eg.1,3-6)
1
NOTE: The Service Type must be the same as the Service Type at the WDM interface of the 52TOM board.
- Configure an OTU1 cross-connection between the 3(RX1/TX1) interface and the 201(ClientLP1/ClientLP1) interface on 52TOM board.
- Set Service Type in the WDM Interface window of the TN52TOM board. For details, see Configuring the Service Type
NOTE: When configuring internal cross-connections for Any services on the TN52TOM board. set the service type to the same as the type of services, which are encapsulated into the OTU1 services received on the client side of the TN52TOM board. For example, if FE services are encapsulated into OTU1 services on the upstream board of the TN52TOM board, set the service type to FE when configuring the internal cross-connections for Any services on the TN52TOM board.
- Configure internal cross-connections of the Any service on the 52TOM board to reshuffle the Any services on the board.
NOTE:
In this scenario, for Any services, only the FE, GE, FC100, FICON, DVB-AS, DVB-SDI, ESCON, and FDDI services can be accessed.
- Configuring an Any cross-connection in the 52TOM board.
Parameters Value Level
ANY
Service Type
FE
Direction
Bidirectional
Source Slot
Shelf2(Subrack2)-15-52TOM
Source Optical Port
233(AnyLP1/AnyLP1)
Source Optical Channel (eg.1,3-6)
1
Sink Slot
Shelf2(Subrack2)-15-52TOM
Sink Optical Port
237(AnyLP5/AnyLP5)
Sink Optical Channel (eg.1,3-6)
1
NOTE: The Service Type must be the same as the Service Type at the WDM interface of the 52TOM board.
Services of the AnyLP1 port can only be configured on the AnyLP5 and AnyLP6 ports. Services of the AnyLP2 port can only be configured on the AnyLP7 and AnyLP8 ports. The rest may be deduced by analogy.
- Configuring an Any cross-connection in the 52TOM board.
- Configure ODU0 cross-connections between the 52TOM and 52NS2 boards.