Configuration Process

This section considers station A as an example to describe the configuration process of the 52TOM board.

Precautions

NOTE:

In Cascading ODU0 mode (Any->ODU0[->ODU1]) mode, the OptiX OSN 8800 T16(NA), OptiX OSN 8800 T32(NA) and OptiX OSN 8800 T64(NA) cannot groom the ODU1 service.
In Cascading ODU0 mode (Any->ODU0[->ODU1]) mode, the OptiX OSN 6800A/3800A cannot groom the ODU0 service.

NOTE:

The client-side optical interface cannot be set to Client Side Color Optical Port.

NOTE:

Services can be input through each client-side optical port at a maximum rate of 1.25 Gbit/s.

NOTE:

Services can be input through the eight pairs of client-side optical ports at a maximum rate of 2.5 Gbit/s.

NOTE:

The total rate of services that are input through each group of ClientLP ports must not be higher than 1.25 Gbit/s.
Only one GE service can be input through each group of ClientLP ports.

NOTE:

Two channels with the same type of services at the ClientLP1 and ClientLP2 ports respectively must not be used at the same time. For example, if the 201(ClientLP1/ClientLP1)-1 service type is configured, the 202(ClientLP2/ClientLP2)-1 service type must not be configured.

Procedure

Set the Working Mode of the 52TOM board. In the NE Explorer, select a 52TOM board, and choose Configuration > Working Mode from the Function Tree. Set Board Working mode to Cascading and then set Port Working Mode to ODU0 mode (Any->ODU0[->ODU1]). For details, see Configuring the Working Mode of the 52TOM Board.
In the NE Explorer, select the desired board , and choose Configuration > WDM Interface from the Function Tree. Configure the Service Type at the WDM Interface of the 52TOM. For details, see Configuring the Service Type.

Configure the cross-connections from the RX/TX ports to the ClientLP ports on the 52TOM board for the Any services of the board.

Configure the cross-connections from the RX/TX ports to the ClientLP ports on the 52TOM board for the Any services that are input to the board.

NOTE:

In this scenario, for Any services, only the FE, GE, FC100, FICON, DVB-AS, DVB-SDI, ESCON, and FDDI services can be accessed.

Parameters	Value
Level	ANY
Service Type	FE
Direction	Bidirectional
Source Slot	Shelf2(Subrack2)-15-52TOM
Source Optical Port	3(RX1/TX1)
Source Optical Channel (eg.1,3-6)	1
Sink Slot	Shelf2(Subrack2)-15-52TOM
Sink Optical Port	201(ClientLP1/ClentLP1)
Sink Optical Channel (eg.1,3-6)	1

NOTE:

The Service Type must be the same as the Service Type at the WDM port of the 52TOM board.

Repeat 3.a to configure the remaining Any services.

Configure electrical cross-connections for the two ODU0 services between the 52TOM and 52NS2 boards.

NOTE:

In Cascading ODU0 mode (Any->ODU0[->ODU1]) mode, only the OptiX OSN 8800 T16(NA), OptiX OSN 8800 T32(NA) and OptiX OSN 8800 T64(NA) supports this scenario.

Configure a cross-connection for one ODU0 service between the 52TOM and 52NS2 boards.

Parameters	Value
Level	ODU0
Service Type	-
Direction	Bidirectional
Source Slot	Shelf2(Subrack2)-15-52TOM
Source Optical Port	201(ClientLP1/ClentLP1)
Source Optical Channel (eg.1,3-6)	1
Sink Slot	Shelf2(Subrack2)-12-52NS2
Sink Optical Port	161(ODU0LP1/ODU0LP1)
Sink Optical Channel (eg.1,3-6)	1

Repeat 4.a to configure a cross-connection for the other ODU0 service between the 52TOM and 52NS2 boards.

Configure electrical cross-connections for the ODU1 services between the 52TOM and 52NS2 boards.

NOTE:

In Cascading ODU0 mode (Any->ODU0[->ODU1]) mode, only the OptiX OSN 6800A/3800A supports this scenario.

Parameters	Value
Level	ODU1
Service Type	-
Direction	Bidirectional
Source Slot	Shelf2(Subrack2)-15-52TOM
Source Optical Port	161(ODU0LP1/ODU0LP1)
Source Optical Channel (eg.1,3-6)	1
Sink Slot	Shelf2(Subrack2)-12-52NS2
Sink Optical Port	51(ODU0LP1/ODU0LP1)
Sink Optical Channel (eg.1,3-6)	1