Service Type
|
EPL, EVPL(QinQ)
Default: EPL
|
Service type.
|
Direction
|
Unidirectional
|
The transmit direction of the service.
The unidirectional service refers to a service transmitted from the source port to the sink port.
|
Operation Type
|
Add S-VLAN, Transparently transmit S-VLAN, Translate S-VLAN, Strip S-VLAN
|
Sets the operation type of QinQ services. Strip S-VLAN is available only when the service direction is Unidirection. - Add S-VLAN: Indicates to add S-VLAN based on PORT routes.
- Transparently transmit S-VLAN: Indicates to transmit S-VLAN transparently.
- Translate S-VLAN: Indicates to exchange S-VLAN based on PORT routes.
- Strip S-VLAN: Indicates to strip S-VLAN.
|
Source Port
|
PORTn, VCTRUNKn
For example: PORT3
|
The name of the source port.
|
Source VLAN
|
- For 11LEX4, 11LEM24, L4G: 1-4094
- For TBE: 1-4095
|
Sets the VLAN ID of the source port.
Applicable to EPL services.
When it is left blank, it indicates no VLAN exists.
|
Source C-VLAN
|
- For 11LEX4, 11LEM24, L4G: 1-4094
- For TBE: 1-4095
|
Sets C-VLAN of source port, C-VLAN is the client VLAN ID.
When it is left blank, it indicates no C-VLAN exists.
|
Source S-VLAN
|
- For 11LEX4, 11LEM24, L4G: 1-4094
- For TBE: 1-4095
|
Sets S-VLAN of source port, S-VLAN is the service VLAN ID.
Applicable to EVPL(QinQ) services.
|
Sink Port
|
PORTn, VCTRUNKn
For example: PORT3
|
The name of the source port.
|
| Sink VLAN |
- For 11LEX4, 11LEM24, L4G: 1-4094
- For TBE: 1-4095
|
Sets the VLAN ID of the sink port.
Applicable to EPL services.
When it is left blank, it indicates no VLAN exists.
|
Sink C-VLAN
|
- For 11LEX4, 11LEM24, L4G: 1-4094
- For TBE: 1-4095
|
Sets C-VLAN of source port, C-VLAN is the client VLAN ID.
When it is left blank, it indicates no VLAN exists.
|
Sink S-VLAN
|
- For 11LEX4, 11LEM24, L4G: 1-4094
- For TBE: 1-4095
|
Sets S-VLAN of sink port, S-VLAN is the service VLAN ID.
Applicable to EVPL(QinQ) services.
|
C-VLAN Priority
|
- For Add S-VLAN: AUTO
- For Transparently transmit S-VLAN, Translate S-VLAN, Strip S-VLAN: -
|
Displays the priority of C-VLAN.
NOTE: The QinQ services of only the TBE board are displayed.
AUTO: The priority must be consistent with that of the source C-VLAN.
-:
The priority cannot be changed.
|
S-VLAN Priority
|
- For Add S-VLAN: AUTO, Priorityn
For example: Priority0
Default: AUTO
- For Transparently transmit S-VLAN, Translate S-VLAN, Strip S-VLAN: -
|
Sets the priority of S-VLAN. The smaller the value is, the lower the priority is.
For example: Priority0 has a lower priority than Priority7.
NOTE: The QinQ services of only
the TBE board are displayed.
AUTO: The priority must be consistent with that of the source C-VLAN.
-: The priority cannot be changed.
|
OAM Enable
|
Enabled, Disabled
|
Sets whether the link should transmit OAM frames. OAM frames are used to determine the path state of the end receiving VLAN SNCP services. Hence, when VLAN SNCP services are configured, make sure that the OAM Enable of
the transmit services on the transmit end is set to Enabled.
NOTE: When creating VLAN SNCP protection on the TBE board, do not enable OAM at the transmit end.
|
Port
|
-
|
Displays the name of a port.
|
Port Type
|
UNI, C-Aware, S-Aware
|
Sets the network attributes for a port.
If the port is of the UNI type, the port processes the tag attributes in 802.1Q and the port has the Tag, Access and Hybrid attributes.
If
the port is of the C-Aware type, the port does not process the tag attributes in 802.1Q. It determines that the data packet carries the C-VLAN tag and processes only the data packet that has the C-VLAN tag.
If the port is of the S-Aware type,
the port does not process the tag attributes in 802.1Q. It determines that the data packet carries the S-VLAN tag and processes only the data packet that has the S-VLAN tag.
QinQ services support C-Aware and S-Aware ports.
EPL services support
only UNI ports.
|
Port Enabled
|
Enabled, Disabled
|
Enables or disables a port.
Enabled: This port can access services.
Disabled: This port cannot access services.
|
TAG
|
Tag Aware, Access, Hybrid
Default: Tag Aware
|
TAG is used to set the type of the processed messages. The tag aware port only processes the messages with a tag, and those messages without a tag are discarded. However, the Access port is
quite the contrary. The hybrid port processes the two types of messages. It adds a tag to the messages without a tag according to the VLAN ID of this port.
|