Port
|
slot number-board name-port number
|
Displays the port of the IF board.
|
IF Channel Bandwidth
|
7MHz, 14MHz, 28MHz, 40MHz, 56MHz
|
Specifies the IF channel bandwidth of the port.
The channel frequency bandwidth, that is, channel bandwidth or channel interval, depends on the spectrum of the signal transmitted, or depends on the capacity and the modulation mode used.
|
AM Mode
|
Symmetric, Asymmetric
Default value: Asymmetric
|
Specifies the AM mode.
|
AM Status
|
Disable, Enable
Default value: Disable
|
Enables or disables the AM.
If the AM is enabled, the assured capacity and full capacity modulation modes can be edited, but the manually specified modulation mode is grayed.
If the AM is disabled, the manually specified modulation
mode can be edited, but the assured capacity and full capacity modulation modes are grayed.
|
Modulation Mode of Guaranteed AM Capacity
|
QPSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM, 512QAM, 1024QAM, 2048QAM, QPSKStrong, 16QAMStrong, 512QAMLight, 1024QAMLight,QPSKStrong_250M, QPSKStrong_500M |
Specifies the lowest-order modulation scheme that the AM function supports. This parameter is set according to the network plan. Generally, the value of this parameter is determined by the service transmission bandwidth
that the Hybrid radio must ensure and the availability of the microwave link that corresponds to this modulation scheme.
This parameter is configurable only when AM Status is set to Enable.
NOTE: This parameter can be set to 512QAM, 1024QAM, QPSKStrong, 16QAMStrong, 512QAMLight, or 1024QAMLight only when Running Mode of the board is IS3.
|
Modulation Mode of the Full AM Capacity
|
QPSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM, 512QAM, 1024QAM, 2048QAM, QPSKStrong, 16QAMStrong, 512QAMLight, 1024QAMLight,QPSKStrong_250M, QPSKStrong_500M |
Specifies the highest-order modulation scheme that the AM function supports. This parameter is set according to the network plan. Generally, the value of this parameter is determined by the bandwidth of the services that
need to be transmitted over the Hybrid radio and the availability of the microwave link that corresponds to this modulation scheme.
This parameter is configurable only when AM Status is set to Enable.
NOTE: This parameter can be set to 512QAM, 1024QAM, QPSKStrong, 16QAMStrong, 512QAMLight, or 1024QAMLight only when Running Mode of the board is IS3.
|
Manual Modulation Mode
|
QPSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM, 512QAM, 1024QAM, 2048QAM, QPSKStrong, 16QAMStrong, 512QAMLight, 1024QAMLight,QPSKStrong_250M, QPSKStrong_500M |
specifies the modulation scheme that the microwave link uses for signal transmission.
This parameter is configurable only when AM Status or AMAC Status is
set to Disable.
NOTE: This parameter can be set to 512QAM, 1024QAM, QPSKStrong, 16QAMStrong, 512QAMLight, or 1024QAMLight only when Running Mode of the board is IS3.
|
Enable E1 Priority
|
Enable, Disable
|
Enables or disables processing of E1 services based on priority levels.
If this parameter is set to Enable, NEs on a channel process E1 services
according to the preset priorities when the channel deteriorates. Specifically, E1 services are transmitted or discarded accordingly.
NOTE: This parameter is configurable only when AM Enable Status is set to Enable.
|
Guaranteed E1 Capacity
|
For example: 40
|
Specifies the minimum number of E1 services that can be transmitted in hybrid mode. - If AM Enable Status is set to Enabled, this parameter needs to be set according to IF Channel Bandwidth, Modulation Mode of Guaranteed AM Capacity, and the actually
transmitted services.
- If AM Enable Status is set to Disabled, this parameter needs to be set according to IF Channel Bandwidth, Manual Modulation Mode, and the actually transmitted
services.
- For the ISU2 and ISX2 boards, this parameter is available when IF Service Type is Hybrid(Native E1+ETH).
- For the ISX2 boards, the Guaranteed E1 Capacity may vary with the XPIC Enabled value (Enabled or Disabled) although the IF channel bandwidth and modulation
mode are the same.
- The Guaranteed E1 Capacity value varies with boards. For details, see technical specifications of the boards in the related device documentation.
NOTE: You need to check the maximum capacity that can be specified currently to ensure that the value of this parameter does not exceed the limit.
|
E1 Capacity
|
For example: 4
|
Specifies the number of E1 services that can be transmitted in hybrid mode.
|
Full E1 Capacity
|
For example: 10
|
Specifies the maximum number of E1 services that can be transmitted in hybrid mode.
|
Tx Modulation Mode
|
QPSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM, 512QAM, 1024QAM, 2048QAM, QPSKStrong, 16QAMStrong, 512QAMLight, 1024QAMLight,QPSKStrong_250M, QPSKStrong_500M |
Displays the modulation mode of signals at the transmit end.
|
Rx Modulation Mode
|
QPSK, 16QAM, 32QAM, 64QAM, 128QAM, 256QAM, 512QAM, 1024QAM, 2048QAM, QPSKStrong, 16QAMStrong, 512QAMLight, 1024QAMLight,QPSKStrong_250M, QPSKStrong_500M |
Displays the modulation mode of signals at the receive end.
|
Guaranteed AM Capacity (Mbit/s)
|
-
|
Displays the minimum AM service capacity of the link.
|
Full AM Service Capacity (Mbit/s)
|
-
|
Displays the maximum AM service capacity of the link.
|
Transmitted AM Service Capacity (Mbit/s)
|
-
|
Displays the transmitted AM service capacity of the link.
|
Received AM Service Capacity (Mbit/s)
|
-
|
Displays the received AM service capacity of the link.
|