This section describes the procedure for configuring the IP over DCN solution in a single OSPF area to import static routes of third-party equipment and the NMS to an OSPF area consisting of OptiX radio transmission equipment.
Context
NOTE: In this configuration example, only the configuration information about the typical NEs, NE1, NE3, NE4, and NE6 is provided.
Procedure
- Change the NE IDs.
The values for the related parameters are provided as follows.
Parameter Value NE1 NE3 NE4 NE6 New ID 1 3 4 6 New Extended ID 9 9 9 9 - Set NE communication parameters.
The values for the related parameters are provided as follows.
Parameter Value NE1 NE3 NE4 NE6 IP Address 10.0.0.1 129.9.0.3 129.9.0.4 129.9.0.6 Gateway IP Address 0.0.0.0 0.0.0.0 0.0.0.0 0.0.0.0 Subnet Mask 255.255.0.0 255.255.0.0 255.255.0.0 255.255.0.0 - Configure the DCC channels.
The values for the related parameters are provided as follows.
Parameter Value IF Port (NE1) IF Port (NE3) IF Port (NE4) IF Port (NE6) Enabled/Disabled Enabled Enabled Enabled Enabled Channel D1 (default value of an IP port in PDH radio mode whose capacity is lower than 16 E1s)
D1-D3 (default values of other IF ports)
D1 (default value of an IP port in PDH radio mode whose capacity is lower than 16 E1s)
D1-D3 (default values of other IF ports)
D1 (default value of an IP port in PDH radio mode whose capacity is lower than 16 E1s)
D1-D3 (default values of other IF ports)
D1 (default value of an IP port in PDH radio mode whose capacity is lower than 16 E1s)
D1-D3 (default values of other line ports)
Protocol Type TCP/IP TCP/IP TCP/IP TCP/IP - Configuring Ports Where Inband DCN Needs to Be Enabled.
Set parameters as follows.
Parameter Value NE3's GE Port Connected to NE4 NE4's GE Port Connected to NE3 Enabled Status Enabled Enabled Protocol Type TCP/IP TCP/IP - Set OSPF parameters.
The values for the related parameters are provided as follows.
Parameter Value NE1 NE3 NE4 NE6 OSPF Status Enabled Enabled Enabled Enabled Static route Enabled Disabled Disabled Enabled LAN Interface Disabled Enabled Enabled Enabled - Create static IP routes.
The values for the related parameters are provided as follows.
Parameter Value NE1 NE6 Destination Address 11.0.0.100 130.9.0.7 Subnet Mask 255.255.255.255 255.255.255.255 Gateway 10.0.0.200 130.9.0.7 - Disable the extended ECC function for NE1 and NE6.
For NE1 and NE6, click Stop to disable the extended ECC function in Auto mode.
- Query the IP routes.
In the NE Explorer, choose , and click Query.
The expected query results are provided as follows.
For NE1:
- Routes to the NE IP addresses 129.9.0.2, 129.9.0.3, 129.9.0.4, 129.9.0.5, 130.9.0.6, and 130.9.0.7, with the gateway whose IP address is 129.9.0.2
- Route to the network segment 10.0.0.0, with the gateway whose IP address is 10.0.0.1
- Route to the NE IP address 11.0.0.100, with the gateway whose IP address is 10.0.0.200
For NE6:
- Routes to the NE IP addresses 129.9.0.2, 130.9.0.3,129.9.0.4, and 129.9.0.5, with the gateway whose IP address is 129.9.0.5
- Routes to the NE IP addresses 10.0.0.0, 10.0.0.1, and 11.0.0.100, with the gateway whose IP address is 129.9.0.5
- Route to the NE IP address 130.9.0.7, with the gateway whose IP address is 130.9.0.7
- Create NEs
by searching for the NEs on the centralized NMS.
Search for NEs by using 10.0.0.1 as IP Address of GNE.
Normally, all NEs can be created on the centralized NMS.
Follow-up Procedure
To ensure communication between the third-party NMS and the third-party gateway NE, perform the following settings:
- On the third-party gateway NE, configure a static route to the third-party NMS (IP address: 11.0.0.100). The gateway uses the IP address of NE6, 130.9.0.6.
- On the third-party NMS, configure a static route to the third-party gateway NE whose IP address is 130.9.0.7. The gateway uses the interface IP address of the router, 11.0.0.200. Alternatively, you can set the IP address 11.0.0.200 to be the default gateway of the third-party NMS.
- On the router, configure the routes according to the third-party gateway NE whose IP address is 130.9.0.7.